Basic Testing of ITpipes Mobile
Once ITpipes Mobile has been setup it is recommended that it be tested to verify functionality.
Do the following to do a basic test of ITpipes Mobile:
From the Project View select .
Selectto create a new asset.
Fill out the required Asset header fields in the data entry, if applicable.
Selectto start a new inspection.
Fill out the required Inspection header fields in the data entry, if applicable.
Select to start recording.
While either driving the camera unit or pulling the cable out, make several observations by doing the following:
To achieve desired codes, select Group, Descriptor, and Modifier options from the individual drop downs.
Input the distance of the observation in the distance field.
To achieve desired codes regarding NASSCO templates:
Access Point Manhole: We can select the "AMH" code in the Observation List, ensure that the Distance is marked "0", add Remarks, and single-click the orange check once finished to add the code.
Miscellaneous Water Level: We can then select the "MWL" code in the Observation List, ensure the Distance is marked "0", add the Percentage and Remarks, and single-click the orange check to add that code as well.
Ending Access Point Manhole: As we end the inspection and all Observation codes have been added, we can select the "AMH" code once more, add the Distance and/or Remarks, and single-click the orange check to finish the Inspection.
Input Value 1st dimension, Value 2nd dimension, Value Percent, Joint, and Continuous. Note: These options are per code and will change with each code. Required fields are marked with a red.
Either select the From clock position and/or To clock position from the drop downs or on the clock image.
Left click provides the From clock position.
Right click provides the To clock position.
Input remarks if desired.
Once completed select to save the observation. Note: The snapshot that will be taken, will be from the video’s current location.
Select to stop the recording. Once this is selected ITpipes Mobile will go to Inspection Review.
Selectto proceed back to Asset.
Verify that video and snapshots exist under the media panel.
The full ITpipes Mobile Users Manual can be found here.
Do the following to do a basic test of ITpipes Mobile:
From the Project View select .
Selectto create a new asset.
Fill out the required Asset header fields in the data entry, if applicable.
Selectto start a new inspection.
Fill out the required Inspection header fields in the data entry, if applicable.
Select to start recording.
While either driving the camera unit or pulling the cable out, make several observations by doing the following:
To achieve desired codes, select Group, Descriptor, and Modifier options from the individual drop downs.
Input the distance of the observation in the distance field.
To achieve desired codes regarding NASSCO templates: Access Point Manhole: We can select the "AMH" code in the Observation List, ensure that the Distance is marked "0", add Remarks, and single-click the orange check once finished to add the code. Miscellaneous Water Level: We can then select the "MWL" code in the Observation List, ensure the Distance is marked "0", add the Percentage and Remarks, and single-click the orange check to add that code as well. Ending Access Point Manhole: As we end the inspection and all Observation codes have been added, we can select the "AMH" code once more, add the Distance and/or Remarks, and single-click the orange check to finish the Inspection.
Input Value 1st dimension, Value 2nd dimension, Value Percent, Joint, and Continuous. Note: These options are per code and will change with each code. Required fields are marked with a red.
Either select the From clock position and/or To clock position from the drop downs or on the clock image.
Left click provides the From clock position.
Right click provides the To clock position.
Input remarks if desired.
Once completed select to save the observation. Note: The snapshot that will be taken, will be from the video’s current location.
Select to stop the recording. Once this is selected ITpipes Mobile will go to Inspection Review.
Selectto proceed back to Asset.
Verify that video and snapshots exist under the media panel.
Related Articles
GIS Map Testing for ITpipes Mobile
Once the map is setup inside of ITpipes Mobile it is recommended that it be tested to verify functionality Do the following to do a map test inside ITpipes Mobile: Open the project the map was attached to. Confirm the map background is visible. If ...ITpipes Mobile in the Field or Office
While ITpipes Mobile can be used on a laptop or pc, and that device could be in the field or office, ITpipes Mobile is designed for field use. ITpipes Mobile does not have all the functionality of ITpipes Web for editing, review, and reporting. ...ITpipes and ESRI Documentation
Table of Contents Introduction ITpipes integration with an ESRI geographic information system (GIS) is a powerful way to leverage the capabilities of these advanced systems. This document covers various components of this integration. The purpose of ...ITpipes Education - User's Manual, Quickguides, Training Videos
Users Manual Here is a link to ITpipes Users Manuals: ITpipes Web ITpipes Mobile ITpipes Sync Quickguides ITpipes Mobile ITpipes Sync Training Videos Links to available training videos. Best when viewed full screen. ITpipes Web Creating a WO - ...ITpipes Implementation Timeline for Mobile, Sync, Web and Cloud
This is a general timeline for an ITpipes implementation with products including Mobile, Sync, Web and Cloud*. Please keep in mind this timeline does vary based on all requirements being met, based on client resources and responsiveness, legacy data ...